Clutch Puch Maxi

• Clutch thrustplate
• Puch Maxi E50 Kickstart

• Driver gear kickstarter
• Puch E50
  
  For:
• Puch Maxi
• Puch Magnum X

• Clutch nut
• E50 Kickstart engine
• Puch
• M10X1

• Gear set Kickstart
• gearing as original
• 10-Pieces
  
  Set contains:
• Primary axle
• Clutch housing + Pressure plate
• Kickstart axles + Drivers
• Shimrings
  
  Fits on:
• Puch E50 3- and 4-bearing Kickstart engines

• Sunk Crosshead
• M6X25
• Galvanized
• Din 965

• Kickstart cover
• Puch
• For Kickstart engines E50

• Oil filler cap
• Plug on the bottom side of the engine
  To use for;
• Puch Maxi

Fiber ring Filler Puch Maxi

• Seal kickstart
• Puch Rider Macho
• 16 X 25 X 7
• Puch E50 Engines

• Plastic Kickstart guide
• Puch Maxi with kickstart engine ( E50 )
• Puch Magnum X

• Kickstart spring
• For Puch Maxi with Kickstart ( E50 )
• Puch Magnum X

• Kickstart Rubber
• Puch Rider Macho
• Length 65MM
• Inside diameter 8MM
• Outside diameter 15MM

• Kickstart pedal
• Chromed
• Puch Maxi E50

• Kickstarter Woodruff Key
• 9.5MM
• Puch Macho
• Also Fits on Vespa remake cranks

M6 Body disc
Galvanized
( 25 X 1.5 )
Din 9021

• Nut M6
• Galvanized
• Din 934

• Kickstartaxle
• Puch Maxi E50

• Kickstart cover gasket
• Puch Maxi
• Puch Rider Macho

• Kickstart cover gasket
• Puch Rider Macho
• 0.5MM / Blue

• Spring washer clutch nut
• For Puch E50 kickstart engines

• Clutch shoes set
• A-quality Surflex
• Puch Maxi ( Run-up block )
• 3 Claw.
• Without keyway, also usable for crankshafts with a keyway, clutch is conical on the crankshaft.

• Clutch shoes set
• Puch Rider Macho ( Kick-start engine)
• 3 Claw
• ( 6MM screw thread can be tapped in, is also pre drilled / for use of clutch puller )
• Without keyway, also to use on crankshafts with a keyway, Clutch is conical attached on the crankshaft

• Clutch set
• Puch Maxi ( Run-up block )
• 3 Claw
• Without keyway, also to use on crankshafts with a keyway, Clutch is conical attached on the crankshaft

• Clutch conversion kit
• For Racing purposes
• Aramide / Kevlar clutch segments
• Fits on Surflex and Replica clutches
• Puch E50 Run-up and Kickstart engines
  
  Set contains:
• 3x Aramide clutch segments
• 2x Spring set (50N/mm & 100N/mm)
• 1x Reinforcement plate stainless steel
• 3x Allen bolt clutch segment
• 3x Allen bolt reinforcement plate
• 3x Circlip
  
  Note:
• Let the clutch soak in clutch oil for at least 6 hours before installation
• Clutch baseplate not included
• Adjustments are required for conversion, see Manual
  
  {{widget type="Amasty\ProductAttachment\Block\Widgets\AttachmentsList" widget_type="3" show_icon="1" show_filesize="1"}}

• Straight cut gear set
• Special hardened steel
• CNC produced
• Balanced
• Ratio 19:94
• Fits the original clutch
  
  Set contains:
• Primary axle (700 gram)
• Clutch bell (278 gram)
• Bronze bushing
  
  Fits on:
• Puch E50 3- and 4-bearing Kickstart engines

Circlip

• Crankshaft
• Clutch side
• Puch Maxi
• A Piece

• Bearing SKF
• 6203 C3
• Inner diameter 17MM
• Outer diameter 40MM
• Width 12MM
  
  Usable for:
• Puch Maxi, Left side Crankshaft
• Puch Maxi, Sprocket axle
• Yamaha FS1 Gears
• Zundapp 3/4/5 Gears, Crankshaft Left
• Zundapp 3 Gears, Front sprocket
• Tomos A3/A35, Crankshaft Left/Right
• Honda MT/MB, Balance axle Right
  
  

• Outer ring
• For 6203 Bearing
• Puch Maxi

• Circlip.
• For mounting the frontsprocket
• Also fits on Footrests bar
• Puch Maxi

• Front sprocket
• 15 Teeth
  Various Puch models
• Puch Maxi
• Puch MV / VS
• Puch Magnum
• Puch Magnum X
• Puch Monza

• Front sprocket
• 16 Teeth
  Various Puch models
• Puch Maxi
• Puch MV / VS
• Puch Magnum
• Puch Magnum X
• Puch Monza

• Front sprocket
• 14 Teeth
  Various Puch models
• Puch Maxi
• Puch MV / VS
• Puch Magnum
• Puch Magnum X
• Puch Monza

Shimring Clutch housing Rear 1.0MM

Puch Maxi.

17X24X1.0

Assortiment set Shims.
Puch Run-up & kickstart engines.
Set contains;

• 2 X Shimring Kickstart shaft
• 2 X Shimring Clutch 0.20MM
• 5 X Shimring Clutch frontside 0.30MM
• 5 X Shimring Clutch frontside 1.00MM
• 2 X Shimring Clutch frontside 1.50MM
• 2 X Shimring Clutch rearside 0.20MM
• 5 X Shimring Clutch rearside 0.30MM
• 5 X Shimring Clutch rearside 1.00MM
• 2 X Shimring Clutch rearside 1.50MM
  
  
  

• Clutch housing
• Model as original
• 21 Teeth
• With bronze bushing
  
  Note:
• Check that your old housing has the same number of teeth and the same direction of rotation.
  
  Fits on:
• Puch E50 Push-start engines

• Clutch housing
• Model as original
• 21 Teeth
• With bronze bushing
  
  Note:
• Check that your old housing has the same number of teeth and the same direction of rotation.
  
  Fits on:
• Puch E50 Kickstart engines
• Puch Magnum X

• Shimring
• Clutch housing Front
• Puch Maxi
• 15X21X1.0MM

Circlip Axle.
Size; 15MM.
Din 471

• Bearing Sleeve
• Brass
• Puch Maxi
  
  
• Note, Product needs rework with waterproof sandpaper to be made fitting